Nass Magnet Coil Core 14.6mm, H 42mm, W 30mm, L 39mm 12v to 380v

Nass Magnet Solenoid Valve Coil System 13/30\nBore: 14.6mm, top plate 10mm\nHeight: 42mm\nWidth: 30mm\nLength: 39mm\nED 100%, Class H, protection according to EN 60529 IP65 with connector.\nConnection: according to: DIN EN 175301803-A\nMaterial: Thermoset resin\nVoltage tolerance: -10% to +10%\nAmbient Temperature: -20°C +50°C\n\nVoltages:\n12vAC 50/60Hz (113-030-0044 or use 12vdc with bridge rectifier connector)\n12vDC 15 Watt 9.7Ω, (113-030-0047, previously 2506442)\n24vAC 19.3VA 6.2 Ω, (113-030-0040, previously 0543 00.1-00/5768, 25002865)\n24vDC 15 Watt 37.8 Ω, (113-030-0028, previously 0543 00.1-00/5753, 2503154).\n48vAC 50/60Hz 19VA 24.3 Ω, (113-030-0052, previously 2507966)\n48vDC 10.9 Watts 20.5 Ω, (113-028-0044)\n64vAC 37.8 Ω\n110vAC 50/60Hz 17.6VA 135 Ω (113-030-0037, Previously 054300.1-00/6869, 2502864)\n110vDC 17 Watts 69 Ω, (113-030-0053, previously 25010353)\n220vDC 18 Watt 338 Ω, (113-030-0051)\n240vAC 50/60Hz, 17.6VA 701 Ω, (113-030-0203)\n380vAC 22VA 2002 Ω, (previously 0543 00.1-00/6755, 25007935)\n\nFits all Shako solenoid 2/2 way 3/8 to 2\" valves: PU220A, PU225A, PU225D, PU225DN, PU225S, PU225H, PU225X, SPU220 and SPU225 series

6281 in stock Model: 22003

Electrical Connector 2P+E Form A without circuit IP65 PG9 0-250v

EN 175301-803 (DIN43650A) square electrical connector without circuit for solenoid valves,\nConnection: DIN ISO4400 Form A DIN 43650A 28mm square\nConduit entry: PG9 (cable 6 to 8mm) or M20x1.5mm with grommet removed\nVoltages: 0 to 250 volts AC/DC\nCurrent: 16 Amp maximum\nCircuit: non\nProtection: IP65\n\n2022 model updated with new terminal block, new reference 611-201-0063\n\nIn order to establish a suitable electrical connection, the use of ferrules for fine stranded cables are mandatory. Be aware that the wire (conductor) cross-section affects the maximum current load (Amp) capacity.

4189 in stock Model: DIN2

3/4 BSP Motor ball valve WRAS 9-24vAC/DC or 110-240vAC Open/Close + Failsafe 10 Bar ABVM06S

3/4 inch Motor Actuated WRAS Ball Valve Mini series ABVM06S ®.\n\nMotor Actuator:\nOpen/Close: 4 to 6 seconds.\nIncludes: visual position indication.\nTemperature (ambient): -15°C to +50°C. \nCycle life: 100,000+ open/close, 100% rated.\nPower Consumption: 1 to 5 watts when moving.\nControl options: Failsafe return or Power Open/Close.\nPower supply: 9-24v 2 amp, 110-240v 500mA recommended.\nVoltage: 9 to 24 volts AC/DC or 110 to 240 volt AC with multi voltage technology.\n\nBall Valve: \nBore: 20.0mm\nPressure: 0 to 10 Bar\nBody: 304 stainless steel\nWRAS Certificate 2012107\nPort 3/4 BSP, optional NPT thread\nSeals: PTFE + EPDM (WRAS Approved).\nTemperature (media): -15°C to +100°C. \nMedia: air or water suitable with 304 stainless steel, EPDM + PTFE.\n\nOptions to choose.\n1. Failsafe Closed = Power ON will OPEN - Power OFF will automatically CLOSE with reserve power. (ABVM06S/9AR + ABVM06S/2AR)\n\n2. Failsafe Open = Power ON will CLOSE - Power OFF will automatically OPEN with reserve power. (ABVM06S/9AR-NO + ABVM06S/2AR-NO)\n\nFailsafe actuators require minimum 30 second power ON for recharging. \n\n3. Power Open/Close = connect RED +ve and BLACK -ve wires, GREEN wire is the control wire. \nPower to GREEN valve opens or power off valve closes. (ABVM06S/2 and ABVM06S/9)\n\n4. Control voltage 9 to 24v AC/DC or 110 to 240vAC.\n\nOther options.\n\nManual Override = Button Lift + Twist will open/close valve and disengage motor, push back down to re-engage motor. \nAvailable low voltage only. (ABVM06S/9AR-MO, ABVM06S/9AR-NO-MO, ABVM06S/9-MO)\n\nABVM Weather Cover (recommended for use outdoors or wet environments).\n\nE2 Position Switches = Position OPEN and CLOSED end of travel confirmation switches.\nVolt free feed back (no voltage supplied from actuator). \nSwitch rating 0 to 36vDC 0.4 Amp Max. (ABVM06S/9AR-E2, ABVM06S/2AR-E2, ABVM06S/9-E2, ABVM06S/2-E2) \n\nTechnical Specifications \n\nSpeed: \n9-24 volt: Open 4 second / close 4 seconds\n110-240 volt: Open 4 seconds / Close 6 seconds.\n\nStart Power\n9-24 volt: peak current can reach 2.08A for 5ms (0.005 seconds) after first start and capacitors not charged.\n\nMoving Power:\n9-24 volt: 1 to 1.2 Watts, 50mA to 130mA. (Back EMF 3 to 5 Volts over nominal. 9v=130mA, 12v=100mA, 24v=50mA.) \n110-240 volt: 2 to 5 Watts, 50 to 100mA. \n\nMaximum Voltage:\nActuators without manual override can operate from 6 to 24v AC/DC, where 24 volts is absolute maximum.\nActuators with manual override can operate from 9 to 35 volts AC/DC. \n\nDestruction Test.\nOn the 26th November 2020 at around 10.40am we connected an ABVM to a dry 1/2 BSP mini ball valve with 9-24vACDC failsafe closed actuator to our SVDT22 (digital cycle timer), and set this for 1 cycle every 60 seconds (30 sec power ON Open then 30 Sec power off to Close) 24/7 all day all night non-stop. (except holidays)\n\nAs of 31st May 2023 the valve has opened and closed, 1,311,280 times and still opening and closing perfectly.

2350 in stock Model: ABVM06S

1/4 Brass Solenoid Valve 0-8.5Bar 2/2 Normally Closed 2.3mm PU220AR-02

1/4 Brass solenoid valve Shako PU220AR-02 ®\nFunction: 2/2 way normally closed \nOperation: direct acting\nPort: 1/4 BSP, option NPT thread\nPressure: 0 to 8.5 Bar (AC) or 0 to 7 Bar (DC Voltage)\nBody: Brass\nInternals: stainless steel\nSeals: NBR standard, option FKM, EPDM or HNBR\nMedia: air, water, vacuum, light oils and any other gases and fluids under 40CST that are compatible with the materials of construction.\nOrifice: 2.3mm\nKv flow factor: 2.0 L/Min based on water with 1 Bar pressure drop.\nCoil: low power 4.5 watt IP65 Class F DIN43650B 100% duty rated\nProtection: IP65 with connector (Included)\nCoil option: ATEX EExmIIT4 Temperature Class T4 T130°C Ex mb IIC T4 and Gb Ex mb tb IIIC T130°C Db for hazardous area 21 and 22. \nVoltages: 6vDC, 12vDC, 24vDC, 48vDC, 110vDC and 12vAC, 24vAC, 48vAC, 110vAC and 230vAC.\nIncludes M4x0.8 mounting holes

1355 in stock Model: PU22002AR

1/2 male Water solenoid valve 0.2-10 Bar nylon normally closed 5115BC

1/2 inch plastic water solenoid valve WRAS approved RPE R Mini 5115BC\nFunction: 2/2 way normally closed\nOperation: Pressure assisted (Min 0.2 Bar pressure differential)\nPort: 1/2 BSP male thread\nPressure: 0.2 to 10 Bar \nOrifice: 11.0mm \nKv flow factor: 28.6 L/min based on water with 1 Bar pressure drop.\nBody: Nylon white good grade 30% Glass Filled\nSeals: NBR, option EPDM\nMedia Temperature: +60°C (100% duty rating), +90°C (3 min ON - 5 min off) \nAmbient temperature: +60°C Max\nCoil: \n12vAC 50Hz Holding 5VA 429mA, Inrush 5.9VA 490mA\n12vAC/DC 50Hz Holding 4.4VA 365mA, Inrush 5.2VA, DC 8.5 Watts\n12vDC 5.4 Watts 450mA\n24vAC 50Hz Holding 7.2VA 302mA, Inrush 8.1VA 337mA\n24vDC 6.3 Watts 265mA\n110vAC 50Hz Holding 5VA 70mA, Inrush 8.8VA 80VA \n220/240vAC 50Hz Holding 6.6VA 29.7mA, Inrush 7.6VA 33mA \n\nCoil option: Low power 12vDC 3.2 Watt or 24vDC 3.6 Watt IP00 with faston tag Glass F\nElectrical connection: faston tags 6.3x0.8mm, (option flying lead wires)\nVoltage: 12vDC, 12vAC/DC, 24vDC, 12vAC, 24vAC, 110vAC or 220/240vAC\n\nApprovals: WRAS, KTW and DM174 for drinking water production, transfer and storage, ACS health compliance certificate, ENEC European Norms Electrical Certification, CSV (European Union Aviation Safety Agency), MOCA FCM (Food Contact Materials), NSF food certification for public health protection and option for UL Underwriter Laboratories certified.\n\nThe RPE R Mini 511 water solenoid valve is ideal for most water inlet systems, drinking water applications, electrical taps and washing machine water systems.

952 in stock Model: 5115BC