Nass Magnet Coil Core 14.6mm, H 42mm, W 30mm, L 39mm 12v to 380v

Nass Magnet Solenoid Valve Coil System 13/30\nBore: 14.6mm, top plate 10mm\nHeight: 42mm\nWidth: 30mm\nLength: 39mm\nED 100%, Class H, protection according to EN 60529 IP65 with connector.\nConnection: according to: DIN EN 175301803-A\nMaterial: Thermoset resin\nVoltage tolerance: -10% to +10%\nAmbient Temperature: -20°C +50°C\n\nVoltages:\n12vAC 50/60Hz (113-030-0044 or use 12vdc with bridge rectifier connector)\n12vDC 15 Watt 9.7Ω, (113-030-0047, previously 2506442)\n24vAC 19.3VA 6.2 Ω, (113-030-0040, previously 0543 00.1-00/5768, 25002865)\n24vDC 15 Watt 37.8 Ω, (113-030-0028, previously 0543 00.1-00/5753, 2503154).\n48vAC 50/60Hz 19VA 24.3 Ω, (113-030-0052, previously 2507966)\n48vDC 10.9 Watts 20.5 Ω, (113-028-0044)\n64vAC 37.8 Ω\n110vAC 50/60Hz 17.6VA 135 Ω (113-030-0037, Previously 054300.1-00/6869, 2502864)\n110vDC 17 Watts 69 Ω, (113-030-0053, previously 25010353)\n220vDC 18 Watt 338 Ω, (113-030-0051)\n240vAC 50/60Hz, 17.6VA 701 Ω, (113-030-0203)\n380vAC 22VA 2002 Ω, (previously 0543 00.1-00/6755, 25007935)\n\nFits all Shako solenoid 2/2 way 3/8 to 2\" valves: PU220A, PU225A, PU225D, PU225DN, PU225S, PU225H, PU225X, SPU220 and SPU225 series

6281 in stock Model: 22003

Electrical Connector 2P+E Form A without circuit IP65 PG9 0-250v

EN 175301-803 (DIN43650A) square electrical connector without circuit for solenoid valves,\nConnection: DIN ISO4400 Form A DIN 43650A 28mm square\nConduit entry: PG9 (cable 6 to 8mm) or M20x1.5mm with grommet removed\nVoltages: 0 to 250 volts AC/DC\nCurrent: 16 Amp maximum\nCircuit: non\nProtection: IP65\n\n2022 model updated with new terminal block, new reference 611-201-0063\n\nIn order to establish a suitable electrical connection, the use of ferrules for fine stranded cables are mandatory. Be aware that the wire (conductor) cross-section affects the maximum current load (Amp) capacity.

4189 in stock Model: DIN2

3/4 BSP Motor ball valve WRAS 9-24vAC/DC or 110-240vAC Open/Close + Failsafe 10 Bar ABVM06S

3/4 inch Motor Actuated WRAS Ball Valve Mini series ABVM06S ®.\n\nMotor Actuator:\nOpen/Close: 4 to 6 seconds.\nIncludes: visual position indication.\nTemperature (ambient): -15°C to +50°C. \nCycle life: 100,000+ open/close, 100% rated.\nPower Consumption: 1 to 5 watts when moving.\nControl options: Failsafe return or Power Open/Close.\nPower supply: 9-24v 2 amp, 110-240v 500mA recommended.\nVoltage: 9 to 24 volts AC/DC or 110 to 240 volt AC with multi voltage technology.\n\nBall Valve: \nBore: 20.0mm\nPressure: 0 to 10 Bar\nBody: 304 stainless steel\nWRAS Certificate 2012107\nPort 3/4 BSP, optional NPT thread\nSeals: PTFE + EPDM (WRAS Approved).\nTemperature (media): -15°C to +100°C. \nMedia: air or water suitable with 304 stainless steel, EPDM + PTFE.\n\nOptions to choose.\n1. Failsafe Closed = Power ON will OPEN - Power OFF will automatically CLOSE with reserve power. (ABVM06S/9AR + ABVM06S/2AR)\n\n2. Failsafe Open = Power ON will CLOSE - Power OFF will automatically OPEN with reserve power. (ABVM06S/9AR-NO + ABVM06S/2AR-NO)\n\nFailsafe actuators require minimum 30 second power ON for recharging. \n\n3. Power Open/Close = connect RED +ve and BLACK -ve wires, GREEN wire is the control wire. \nPower to GREEN valve opens or power off valve closes. (ABVM06S/2 and ABVM06S/9)\n\n4. Control voltage 9 to 24v AC/DC or 110 to 240vAC.\n\nOther options.\n\nManual Override = Button Lift + Twist will open/close valve and disengage motor, push back down to re-engage motor. \nAvailable low voltage only. (ABVM06S/9AR-MO, ABVM06S/9AR-NO-MO, ABVM06S/9-MO)\n\nABVM Weather Cover (recommended for use outdoors or wet environments).\n\nE2 Position Switches = Position OPEN and CLOSED end of travel confirmation switches.\nVolt free feed back (no voltage supplied from actuator). \nSwitch rating 0 to 36vDC 0.4 Amp Max. (ABVM06S/9AR-E2, ABVM06S/2AR-E2, ABVM06S/9-E2, ABVM06S/2-E2) \n\nTechnical Specifications \n\nSpeed: \n9-24 volt: Open 4 second / close 4 seconds\n110-240 volt: Open 4 seconds / Close 6 seconds.\n\nStart Power\n9-24 volt: peak current can reach 2.08A for 5ms (0.005 seconds) after first start and capacitors not charged.\n\nMoving Power:\n9-24 volt: 1 to 1.2 Watts, 50mA to 130mA. (Back EMF 3 to 5 Volts over nominal. 9v=130mA, 12v=100mA, 24v=50mA.) \n110-240 volt: 2 to 5 Watts, 50 to 100mA. \n\nMaximum Voltage:\nActuators without manual override can operate from 6 to 24v AC/DC, where 24 volts is absolute maximum.\nActuators with manual override can operate from 9 to 35 volts AC/DC. \n\nDestruction Test.\nOn the 26th November 2020 at around 10.40am we connected an ABVM to a dry 1/2 BSP mini ball valve with 9-24vACDC failsafe closed actuator to our SVDT22 (digital cycle timer), and set this for 1 cycle every 60 seconds (30 sec power ON Open then 30 Sec power off to Close) 24/7 all day all night non-stop. (except holidays)\n\nAs of 31st May 2023 the valve has opened and closed, 1,311,280 times and still opening and closing perfectly.

2350 in stock Model: ABVM06S

1/4 Brass Solenoid Valve 0-150 Bar 2/2 Normally Closed 1.2-5mm

1/4 inch Miniature brass solenoid valve CS Fluid Power AD8000.\nFunction: 2/2 way normally closed\nOperation: direct acting\nPort: 1/4 BSP standard, option NPT or Rc thread.\nPressure: 0 to 150 Bar (depending on orifice and coil power level)\nVacuum: Torr 10-6 Max\nBody: Brass\nInternals: stainless steel\nOrifice: 1.2 mm, 1.6 mm, 2 mm, 3 mm, 4 mm or 5 mm\nKv flow factor: 1 to 9.15 according to orifice, based on water with 1 Bar pressure drop.\nSeals: FKM standard, option EPDM, NBR, Silicone, PTFE, VST, Neoprene, ECO, HNBR or Hypalon. (PTFE must be used for pressures over 30 Bar).\nMedia: air, water, light oils, vacuum, and most other non corrosive fluids under 50CST and gases that are compatible with materials of construction.\nCoil: WPG1 12 watt UL, CSA, CE, IP67 Class H 100% duty rated DIN43650A\nCoil: WPG2 18 Watt UL, CSA, CE and IP67 Class H 100% duty rated\nCoil option: WPA3C 14.3 to 27.5 Watt (according to voltage) IP54 Class H with 30cm flying lead wires 100% duty rated.\nCoil option available AD80**: ATEX EExmIIT4 Temperature Class T4 T130°C Ex mb IIC T4 and Gb Ex mb tb IIIC T130°C Db for hazardous area 21 and 22 Pressure same as 12 Watt WPG1 coil\nVoltages: 12vDC, 24vDC, 48vDC or 24vAC, 48vAC, 110vAC or 230vAC. \nOther options: Manual Over Ride and other custom made options.

1572 in stock Model: AD8000

Male stud push-in airline fitting M5 to 1/2 BSP 4mm to 12mm NPC

Pneumatic Push-in x BSPT Male Straight Connector\n\nMetric Tube Sizes 4mm, 6mm, 8mm, 10mm or 12mm to M5, 1/8, 1/4, 3/8 or 1/2 BSP thread\n\nOne Touch push to connect configuration allow an instant tubing connection\n\nStrong Nickel Plated Brass sleeve disconnection by pressing the sleeve and then simply removing the tube from the fitting\n\nMale thread is Teflon treated ready for use\n\nNickel Plated Brass body ensures anti contamination\nFor use in pneumatic systems upto 9 Bar with maximum temperature of 60 degrees Celsius

1527 in stock Model: NPC