Electrical Connector 2P+E Form A without circuit IP65 PG9 0-250v

EN 175301-803 (DIN43650A) square electrical connector without circuit for solenoid valves,\nConnection: DIN ISO4400 Form A DIN 43650A 28mm square\nConduit entry: PG9 (cable 6 to 8mm) or M20x1.5mm with grommet removed\nVoltages: 0 to 250 volts AC/DC\nCurrent: 16 Amp maximum\nCircuit: non\nProtection: IP65\n\n2022 model updated with new terminal block, new reference 611-201-0063\n\nIn order to establish a suitable electrical connection, the use of ferrules for fine stranded cables are mandatory. Be aware that the wire (conductor) cross-section affects the maximum current load (Amp) capacity.

4189 in stock Model: DIN2

Electrical Connector 2P+E Form A with LED IP65 PG9 10-50v or 70-250v

EN 175301-803 (DIN43650A) form A square IP65 connector with bipolar LED\n28mm square with 2 pins + earth pins 18mm\nConduit entry: PG9 (Cable 6-8mm)\nVoltage 10 to 50 volt or 70 to 250 volt\nMax voltage 250v AC, 300v DC\nMax operating current 10 Amp, Max current 16 Amp\nProtection: IP65 EN 60529 (DIN40050)\nInsulation class: C - VDE 0110\nWorking Temp: -25C to +90C\nTransparent housing: PA\nContact material: CuZn (Au)\nConnector: PA66 + 30% FV

1024 in stock Model: DIN2-LED-AC, DIN2-LED-DC

Electrical Connector 2P+E Form A without circuit IP65 PG11 0-250v CLEAR

EN 175301-803 (DIN43650A) square electrical connector without circuit for solenoid valves\nConnection: DIN ISO4400 Form A DIN 43650A 28mm square\nHousing: Clear\nConduit entry: PG11 (8-11mm cable)\nVoltages: 0 to 250 volts AC/DC\nCurrent: 16 Amp maximum\nCircuit: non\nProtection: IP65

275 in stock Model: DIN2-PG11

Electrical Connector 2P+E Form A without circuit IP65 PG6 0-250v

EN 175301-803 (DIN43650A) square electrical connector without circuit for solenoid valves\nConnection: DIN ISO4400 Form A DIN 43650A 28mm square\nConduit entry: PG6 (4-6mm cable)\nVoltages: 0 to 250 volts AC/DC\nCurrent: 16 Amp maximum\nCircuit: non\nProtection: IP65

153 in stock Model: DIN2-4/6mm-single

Electrical Connector Form A with 20-65% Energy Saving IP65 12-24vDC

Form A EN 175301-803 12-24vDC Pulse Width Modulating 20% to 65% energy saving electrical DIN connector 611-201-1320.\n\nPWM connector will fully energise the valve solenoid to achieve full inrush current. Then, after approximately 100 milliseconds, the PWM circuit reduces the full voltage to a reliable holding power that needs to be adjusted using the 2-1 jumpers to the holding power required by the solenoid valve coil.\n\nThis achieves considerable energy saving, reduces coil heat rise and extends solenoid coil life.\n\nPWM modulating connector jumper settings for the Hold Power Saving\n00..20%, 01..35%, 10..50%, 11..65%\n\nBuy 50 pcs £24.88 each or 100pcs £14.94 each\n\nSimplified guide to setting up.\nWith the pipe system at full load / pressure, reduce the power in single stages until the coil fails to operate correctly, then go back one step.\nExample starting with (00) 20% reduction, then (01) 35%, (10) 50% and (11) 65%, then if coil stops holding so go back to (10) 50%.\n\nThe power reduction is accomplished through pulses with adjustable modulation via relocation of the electrical jumpers for changes in the output voltage. (default setting 20%)\nOperating voltage: 12-24vDC\nMaximum current: 2.5 Amp\nResistance: <15mOhm\nProtection: diode\nDelay = ca. 150 ms\nSwitching Frequency = 2 kHz at 24vDC,\nPulse Ratio of PWM signal = 4 variations,\nPolarity sensitive = Yes\nOvervoltage protection = No.\n\nFor optimum performance, the solenoid coil technical data and electrical parameters must be observed. The PWM circuit includes a protecting diode at the output, eliminating the switch off power surges from the solenoid coil.\nAdditional protecting components such as VDR and TVS diodes are not required.\n\nQuick Overview\nForm: A (Pin Distance 18mm, with circuit with electronics – PWM, Housing: Opaque (Milky), One Piece M20x1.5mm Thread, Manufacturer: Nass Magnet\nMore Information\nGrommets for 6–8 mm, Terminal block: 2 + ground, clamping contact without protecting plate, Electronics: PWM circuit for power sawing, 12–24VDC, NBR profile gasket, black, Standard central fixing screw, Not assembled and single packed in a plastic bag.

144 in stock Model: DIN2-PWM